Fully Developed Flow with Developing Temperature Profile
From ThermalFluidsPedia
Convective heat transfer for steady state, laminar, hydrodynamically developed flow and developing temperature profile in microchannels with both uniform temperature and uniform heat flux boundary conditions were solved by Tunc and Bayazitoglu ^{[1]}^{[2]} using the integral transform technique that is presented below.
Uniform Temperature
The energy equation assuming fully developed flow, including viscous dissipation and neglecting axial conduction, is
The boundary and inlet conditions for constant wall temperature are:
T = T_{s} at r = r_{o} 

T = T_{0} at x = 0 
The fully developed velocity profile with slip boundary condition is used. The slip boundary condition is also used to express the wall temperature jump. The following nondimensional variables are introduced: for temperature (θ), radial coordinate (r^{+}), axial coordinate (x^{+}), and velocity (u^{+}):

The nondimensional energy equation and boundary conditions are obtained through use of the above variables:

θ = 0 at r^{ + } = 1 

θ = 1 at x^{ + } = 0 
where the Graetz number (Gz) and the Brinkman number (Br) are defined as:

where ΔT is the difference between the temperature of the fluid at the wall, Ts', and at the tube entrance, T_{0}, i.e. ΔT = T_{0} − T_{s}.
Uniform Heat Flux
For the case of constant heat flux at the wall, the following nondimensional variables are used:

Upon use of the above nondimensional variables, the nondimensional energy equation for constant wall heat flux can be obtained:

where the centerline symmetric and uniform inlet temperature conditions are the same as eqs. (7) and (8), respectively. However, the boundary condition at the wall is given by .
An integral transform technique based on separation of variables was used by Tunc and Bayazitoglu ^{[1]} to solve this problem. An appropriate integral transform pair was developed. Under the transformation, the variable x^{+} was eliminated from the partial differential governing equation, which transformed the governing equation into an ordinary differential equation.
The effect of viscous heating is presented in the first figure for the constant wall temperature case, where Kn = 0.04 and Pr = 0.7. The inclusion of viscous dissipation causes an increase in Nu. The Nusselt number first reaches the fully developed condition as if there was no viscous dissipation, and then makes a jump to its final value for a given Br.
The second figure to the right shows the effect of viscous heating on the Nusselt number for a uniform wall heat flux. Since the definition of the Brinkman number is different for the uniform wall heat flux boundary condition case, a positive Br means that the heat is being transferred to the fluid from the wall, as opposed to the uniform wall temperature case. For constant heat flux at the wall, the Nusselt number decreases as Br (> 0) increases.
Jeong and Jeong ^{[3]} extended the analysis for application to microchannels of rectangular crosssection, including axial conduction and viscous dissipation.
The configuration for developed flow with developing temperature profile for rectangular microchannels is similar to this picture. The fluid temperature changes from the value T_{0} at the entrance, to the value T_{s} on the walls. The governing energy equation and boundary conditions, including axial conduction and viscous dissipation, for laminar flow are:

T = T_{0} at x = 0 


where H is half the microchannel height, and the wall length in the xdirection is L. The fully developed velocity profile in the rectangular microchannel is:

which satisfies the slip boundary condition:

Defining the following dimensionless variables:

Equations (5.250) and (5.254) are respectively nondimensionalized as:

and

where

The nondimensional boundary conditions are:
θ = 1 at x^{ + } = 0 


where
The effects of the Knudsen number on the Nusselt number variation along a rectangular microchannel neglecting axial conduction and viscous dissipation are shown in Fig. 5.30. For Kn = 0, the fully developed Nusselt number is approximately 7.54, which is the result for a pipe of conventional size (classic Graetz problem). The Nusselt number decreases as Kn increases due to the temperature jump at the wall.
The effect of the Knudsen number on the Nusselt number distribution in a rectangular microchannel with constant wall heat flux is presented in Fig. 5.31.
When the channel is subjected to a constant wall temperature, as , the Nusselt number for is independent of Br and different from that for Br = 0. The thermally fully developed Nusselt number was obtained from the fully developed temperature profile for constant wall temperature and heat flux by Jeong and Jeong (2006).
For constant wall temperature the Nusselt number as (
) is

And for constant heat flux

where . Unless Br is a large negative number, Nu, is always positive.
Cite error:
<ref>
tags exist, but no <references/>
tag was found